GE
Oven Repair
GE Appliances, now owned by Haier, sells a wide choice of everyday single, double and combination wall ovens.
Mon–Sat, 8am–8pm
- 2 oven types
- 6 problems we see
- 5 error codes
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
GE ovens,
specifically.
GE's own-brand wall ovens, such as the 27-inch JK5000 and 30-inch JT5000 and JT5500, use electronic controls that report problems as F-codes. GE Appliances publishes one shared code list for its ranges and wall ovens, and its advice for an unresolved code is to keep the oven off at the breaker until it is serviced.
The GE lineupBuilds2 oven types
Single wall oven · Double wall oven
Called out forOven Not Heating
and 5 more problems on GE
Repairs we do10 repairs, on any make
Diagnostic visit · Bake and broil element repair · Gas igniter and burner repair · Temperature sensor and calibration
Error codesF2 · F3 · F9 · FD · LOC DOOR
5 GE codes with a page of their own
The GE
lineup.
GE builds 2 of the 4 oven types this site covers. Which one decides how the visit is planned.
All oven typesWhat is particular
to GE.
GE-branded wall ovens come in 27-inch and 30-inch single and double versions with electronic touch controls. The code list is shared with GE ranges, so the model number mostly decides which parts are stocked, not what a code means.
One code list for GE ranges and wall ovens
GE's support page covers the F-codes for its electronic ranges and wall ovens together, and the support pages for models like the JT5000 link straight to it. A code on your wall oven means the same thing it would on a GE range.
Breaker off until service
GE says a breaker reset for a minute or two sometimes clears a code, and when it does not, recommends leaving the oven off at the breaker until it is repaired. That is stricter than simply clearing the message.
Steam clean beside self-clean
GE wall ovens like the JT5000 offer Steam Clean for small spills at a lower temperature than Self-Clean. Self-Clean runs hotter and is the only cycle that should lock the door, so lock codes such as F9 tend to appear around it.
A locked door has a set routine
When a GE oven door stays locked, GE's order is: let it cool, cut power, and on an empty oven run a short self-clean to reset the latch. Forcing the latch is the one thing GE says never to do.
Parts
GE wall oven sensors, door locks, bake and broil elements and control boards are widely available. Keypanels on older models can take longer to source.
Repair or replace
Sensor, lock and element repairs on a GE wall oven are usually worth doing given the built-in cut-out. If both the control and the keypanel have failed on an older oven, a replacement is worth pricing.
Book your GE visitWhat we are
called out for.
On GE, most often oven not heating.
All problemsGE error codes
All GE codes
Not a
GE?
GE is one of 30 oven makes on this site. The other 29 each have a page of their own.
All 30 brandsGE oven repair,
where we come out.
9 metros, each with its own page.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions about
GE ovens.
Does a GE wall oven use the same codes as a GE range?
What does GE say to do if a code will not clear?
Is Steam Clean on my GE oven the same as Self-Clean?
My GE oven door is locked after cleaning. Should I pull on it?
Back to your everyday
Book your GE visit.
Have the oven's model number ready — on GE it decides which parts come on the first visit.