AGA eR7 oven
showing 060-100
Codes 060 to 100 on an AGA eR7 mean a thermocouple circuit is open: the control has lost the signal from one of the probes that measure a zone's heat.
Mon–Sat, 8am–8pm
- Temperature sensor
- Temperature sensor and calibration
- Source: AGA
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
What 060-100
actually means.
Codes 060 to 100 on an AGA eR7 mean a thermocouple circuit is open: the control has lost the signal from one of the probes that measure a zone's heat. Without that reading the cooker cannot hold the zone at its setting.
AGA oven display
What to do when 060-100 shows on the ovenKind of codeTemperature sensor
The reading from the temperature probe fell outside what the control will trust, or climbed far higher than the setting. A loose connector or a probe that has drifted is ruled out before the control itself, and a reading that runs away means the breaker goes off first.
Usually leads toTemperature sensor and calibration
Baking that comes out burnt or pale at the usual setting, traced to the sensor, its wiring or an oven that simply needs calibrating.
Shows up asOven Temperature Not Accurate
Recipes come out burnt or underdone at the right setting, and an oven thermometer reads far from the dial.
MakeAGA
A British cooking brand best known for cast-iron heat-storage cookers; in the US it sells ranges, and its ovens are the cavities built into them.
SourceAGA eR7 Field Service Manual, USA and Canada (PDF linked from agarangeusa.com owner's guides)
On the eR7, each thermocouple plug carries four wires, and the technician tests them pair by pair.
Before you book,
in this order.
Each step comes from AGA's own guidance for 060-100 on its ovens. Follow it to the end: the last card says whether this is a visit.
Write down the number the handset shows.
Stop using the affected oven for anything that needs accurate heat.
Book a visit; AGA has the probe checked, its plug on the user panel reseated, and the probe exchanged if it is open.
Still there?
It usually turns into temperature sensor and calibration. Book with the code and the model number.
What not to do
A 060-100 code is not a disagreement between readings. It is a reading that has disappeared.
What you may
notice with it.
The oven problems 060-100 tends to arrive with. Answer these at the oven before anyone is booked.
All problems
Oven Temperature Not Accurate
5 causes, cheapest first
Where 060-100 usually leads
Temperature sensor and calibration.
AGA
ovens.
A British cooking brand best known for cast-iron heat-storage cookers; in the US it sells ranges, and its ovens are the cavities built into them.
AGA oven repairMore AGA codes
Temperature sensor on other makes
In AGA's own words
T/Couple open circuit - Check the thermocouple with a multimeter.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. On the eR7, each thermocouple plug carries four wires, and the technician tests them pair by pair.
AGA 060-100 oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about 060-100.
Can I clear 060-100 myself?
Can a loose plug cause 060-100 on an AGA eR7?
Does 060-100 on an AGA eR7 clear when I switch the cooker off?
Back to your everyday
Still showing 060-100?
Book with the code exactly as shown, the full model number, and whether you can smell gas or burning — with a code, that is where the diagnosis starts.