AGA eR7 oven controls
showing FE
FE appears on the touch panel behind the top left door of an AGA eR7 when the small computer inside that panel stops responding or misbehaves.
Mon–Sat, 8am–8pm
- Communication
- Controls and sensors
- Source: AGA
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
What FE
actually means.
FE appears on the touch panel behind the top left door of an AGA eR7 when the small computer inside that panel stops responding or misbehaves. The three ovens are run from this panel, so the code is about the controls rather than the oven cavities themselves.
AGA oven display
What to do when FE shows on the ovenKind of codeCommunication
The display and the main control board stopped hearing each other, or the board failed its own check. A power dip, a loose ribbon cable or moisture behind the panel is ruled out before either board is replaced, and an oven that stays on through this code is switched off at the breaker.
Usually leads toControls and sensors
Dead keys, a blank or garbled display, an oven that will not switch off or will not respond, traced to the board, the touch panel or their wiring.
Shows up asOven Control Panel Not Responding
The touch controls or buttons do nothing, the display is blank, or some keys work and others do not.
MakeAGA
A British cooking brand best known for cast-iron heat-storage cookers; in the US it sells ranges, and its ovens are the cavities built into them.
SourceAGA eR7 Field Service Manual, USA and Canada (PDF linked from agarangeusa.com owner's guides)
AGA eR7 100 and 150 cookers sold in the US and Canada; FE is one of only three codes the eR7 user panel itself can show.
Before you book,
in this order.
Each step comes from AGA's own guidance for FE on its ovens. Follow it to the end: the last card says whether this is a visit.
Write down FE and note what the ovens were set to when it appeared.
Book a visit; a restart of the panel is the first check, and if FE stays the panel itself is examined.
What not to do
FE is not a heating or temperature code. The roasting, baking and simmering ovens can be perfectly sound while the panel that drives them is the part at issue.
What you may
notice with it.
The oven problems FE tends to arrive with. Answer these at the oven before anyone is booked.
All problems
Oven Control Panel Not Responding
5 causes, cheapest first
Where FE usually leads
Controls and sensors.
AGA
ovens.
A British cooking brand best known for cast-iron heat-storage cookers; in the US it sells ranges, and its ovens are the cavities built into them.
AGA oven repairIn AGA's own words
Error code FE: Touch panel microcontroller unresponsive or malfunctioned.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. AGA eR7 100 and 150 cookers sold in the US and Canada; FE is one of only three codes the eR7 user panel itself can show.
AGA FE oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about FE.
Can I clear FE myself?
Will FE on my AGA eR7 go away by itself?
Is it safe to keep cooking on an AGA eR7 that shows FE?
Back to your everyday
Still showing FE?
Book with the code exactly as shown, the full model number, and whether you can smell gas or burning — with a code, that is where the diagnosis starts.