AGA eR7 oven
showing 130-136
Codes 130 to 136 on an AGA eR7 are a triac error: trouble in the electronic switch and wiring that feed power to a zone's element.
Mon–Sat, 8am–8pm
- Heating
- Bake and broil element repair
- Source: AGA
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
What 130-136
actually means.
Codes 130 to 136 on an AGA eR7 are a triac error: trouble in the electronic switch and wiring that feed power to a zone's element. AGA has the element's connections and resistance checked; an open element is replaced, and if the element tests correctly the main board is next.
AGA oven display · also shown as 130, 131, 132, 133, 134, 135, 136
What to do when 130-136 shows on the ovenKind of codeHeating
The control asked for heat and the cavity did not warm the way it expected. A bake or broil element that has opened or blistered is the usual answer; the wiring to it and the relay that switches it are checked before a board is blamed.
Usually leads toBake and broil element repair
An electric oven that stays cold, bakes only from above or will not broil, traced to the element, its terminals or the relay that feeds it.
Shows up asOven Not Heating
The oven turns on and the display counts, but the cavity stays cold or only lukewarm after a long preheat.
MakeAGA
A British cooking brand best known for cast-iron heat-storage cookers; in the US it sells ranges, and its ovens are the cavities built into them.
SourceAGA eR7 Field Service Manual, USA and Canada (PDF linked from agarangeusa.com owner's guides)
AGA's eR7 manual gives a normal element resistance of 18 to 20 ohms.
Before you book,
in this order.
Each step comes from AGA's own guidance for 130-136 on its ovens. Follow it to the end: the last card says whether this is a visit.
Note the number and which oven or hotplate has gone cool.
Leave the cooker's electrical panel and element wiring alone.
Book a visit so the element and its connections can be measured.
Still there?
It usually turns into bake and broil element repair. Book with the code and the model number.
What not to do
A 130-136 code is not a sensor reading. The zone is failing to get power, not failing to measure heat.
What you may
notice with it.
The oven problems 130-136 tends to arrive with. Answer these at the oven before anyone is booked.
All problems
Oven Not Heating
6 causes, cheapest first
Where 130-136 usually leads
Bake and broil element repair.
AGA
ovens.
A British cooking brand best known for cast-iron heat-storage cookers; in the US it sells ranges, and its ovens are the cavities built into them.
AGA oven repairIn AGA's own words
Triac Fault - Check connections of element circuit showing a triac error at element terminals
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. AGA's eR7 manual gives a normal element resistance of 18 to 20 ohms.
AGA 130-136 oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about 130-136.
Can I clear 130-136 myself?
Is 130-136 on an AGA eR7 always a burned-out element?
Why is only one AGA eR7 oven cold while 130-136 shows?
Back to your everyday
Still showing 130-136?
Book with the code exactly as shown, the full model number, and whether you can smell gas or burning — with a code, that is where the diagnosis starts.