Electrolux wall oven
showing F30
Electrolux lists F30 as an open probe, meaning the control is not getting a reading from a temperature circuit it relies on.
Mon–Sat, 8am–8pm
- Temperature sensor
- Temperature sensor and calibration
- Source: Electrolux
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F30
actually means.
Electrolux lists F30 as an open probe, meaning the control is not getting a reading from a temperature circuit it relies on. Its guide does not specify whether that is the cavity sensor or the food probe.
Electrolux oven display
What to do when F30 shows on the ovenKind of codeTemperature sensor
The reading from the temperature probe fell outside what the control will trust, or climbed far higher than the setting. A loose connector or a probe that has drifted is ruled out before the control itself, and a reading that runs away means the breaker goes off first.
Usually leads toTemperature sensor and calibration
Baking that comes out burnt or pale at the usual setting, traced to the sensor, its wiring or an oven that simply needs calibrating.
Shows up asOven Not Heating
The oven turns on and the display counts, but the cavity stays cold or only lukewarm after a long preheat.
MakeElectrolux
A Swedish appliance group whose US wall ovens focus on convection cooking and combination oven models.
SourceElectrolux owner support: Oven Error Codes and Alarms Guide (read 24 Sep 2026)
Taken from Electrolux's oven error code guide, which lists the code without model numbers or a list of causes.
Before you book,
in this order.
Each step comes from Electrolux's own guidance for F30 on its ovens. Follow it to the end: the last card says whether this is a visit.
Reset the oven: unplug it for 30 seconds or switch the breaker off and on.
Set a short bake and see whether the code comes back as the cavity warms.
If F30 returns, book a visit so the circuit can be tested before a part is chosen.
Still there?
It usually turns into temperature sensor and calibration. Book with the code and the model number.
What not to do
F30 is about a missing signal. It is not the same as F10, which reports too much heat.
What you may
notice with it.
The oven problems F30 tends to arrive with. Answer these at the oven before anyone is booked.
All problems
Oven Not Heating
6 causes, cheapest first
Where F30 usually leads
Temperature sensor and calibration.
Electrolux
ovens.
A Swedish appliance group whose US wall ovens focus on convection cooking and combination oven models.
Electrolux oven repairMore Electrolux codes
Temperature sensor on other makes
In Electrolux's own words
F30 – Open Probe
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Taken from Electrolux's oven error code guide, which lists the code without model numbers or a list of causes.
Electrolux F30 oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F30.
Can I clear F30 myself?
Is F30 on my Electrolux the same as a broken heating element?
What if F30 only appears now and then on an Electrolux oven?
Back to your everyday
Still showing F30?
Book with the code exactly as shown, the full model number, and whether you can smell gas or burning — with a code, that is where the diagnosis starts.