JennAir wall oven
showing F3 E0
F3 E0 on a JennAir wall oven points to the upper oven's temperature sensor, the control, or the wiring between them.
Mon–Sat, 8am–8pm
- Temperature sensor
- Temperature sensor and calibration
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F3 E0
actually means.
F3 E0 on a JennAir wall oven points to the upper oven's temperature sensor, the control, or the wiring between them. Without a trusted reading, the oven cannot hold its set temperature.
JennAir oven display · also shown as F3E0
What to do when F3 E0 shows on the ovenKind of codeTemperature sensor
The reading from the temperature probe fell outside what the control will trust, or climbed far higher than the setting. A loose connector or a probe that has drifted is ruled out before the control itself, and a reading that runs away means the breaker goes off first.
Usually leads toTemperature sensor and calibration
Baking that comes out burnt or pale at the usual setting, traced to the sensor, its wiring or an oven that simply needs calibrating.
Shows up asOven Temperature Not Accurate
Recipes come out burnt or underdone at the right setting, and an oven thermometer reads far from the dial.
MakeJennAir
Whirlpool Corporation's luxury brand, offering wall ovens, steam ovens and speed ovens in two design styles.
SourceJennAir product help: F3 E0 - Wall Oven
JennAir wall ovens; F3 E0 names the upper oven's sensor.
Before you book,
in this order.
Each step comes from JennAir's own guidance for F3 E0 on its ovens. Follow it to the end: the last card says whether this is a visit.
Switch the oven's breaker off for a full minute and turn it on again.
Watch for a minute and check that the upper oven heats normally.
If F3 E0 returns, book a visit.
Still there?
It usually turns into temperature sensor and calibration. Book with the code and the model number.
What not to do
F3 E0 is not the lower oven; that is F3 E1.
What you may
notice with it.
The oven problems F3 E0 tends to arrive with. Answer these at the oven before anyone is booked.
All problems
Oven Temperature Not Accurate
5 causes, cheapest first
Where F3 E0 usually leads
Temperature sensor and calibration.
JennAir
ovens.
Whirlpool Corporation's luxury brand, offering wall ovens, steam ovens and speed ovens in two design styles.
JennAir oven repairMore JennAir codes
Temperature sensor on other makes
In JennAir's own words
There may be a problem with the Upper Oven Temperature Sensor, the Control, or the associated wiring.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. JennAir wall ovens; F3 E0 names the upper oven's sensor.
JennAir F3 E0 oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F3 E0.
Can I clear F3 E0 myself?
Can I use the lower oven of my JennAir while the upper shows F3 E0?
Why is my JennAir running hot or cold with F3 E0?
Back to your everyday
Still showing F3 E0?
Book with the code exactly as shown, the full model number, and whether you can smell gas or burning — with a code, that is where the diagnosis starts.