GE Profile wall oven
showing F4
GE Profile wall ovens share GE's electronic code list, where F4 carries the same meaning as F3: the oven sensor most likely needs replacing.
Mon–Sat, 8am–8pm
- Temperature sensor
- Temperature sensor and calibration
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F4
actually means.
GE Profile wall ovens share GE's electronic code list, where F4 carries the same meaning as F3: the oven sensor most likely needs replacing. Which of the two numbers appears depends on the control in your oven.
GE Profile oven display
What to do when F4 shows on the ovenKind of codeTemperature sensor
The reading from the temperature probe fell outside what the control will trust, or climbed far higher than the setting. A loose connector or a probe that has drifted is ruled out before the control itself, and a reading that runs away means the breaker goes off first.
Usually leads toTemperature sensor and calibration
Baking that comes out burnt or pale at the usual setting, traced to the sensor, its wiring or an oven that simply needs calibrating.
Shows up asOven Temperature Not Accurate
Recipes come out burnt or underdone at the right setting, and an oven thermometer reads far from the dial.
MakeGE Profile
GE Appliances' step-up line, with convection, air fry and combination wall ovens that include speed cooking models.
SourceGE Appliances support: Range & Wall Oven error codes
GE Profile wall ovens with electronic controls, such as PT7050 (built 2013-2019), whose support page links the GE code list.
Before you book,
in this order.
Each step comes from GE Profile's own guidance for F4 on its ovens. Follow it to the end: the last card says whether this is a visit.
Switch the oven off at the breaker for a minute or two.
If F4 returns, stop using the oven and book a visit.
Still there?
It usually turns into temperature sensor and calibration. Book with the code and the model number.
What not to do
F4 is not an Advantium speed-oven humidity sensor code on a regular Profile wall oven; that meaning belongs to the Advantium list.
What you may
notice with it.
The oven problems F4 tends to arrive with. Answer these at the oven before anyone is booked.
All problems
Oven Temperature Not Accurate
5 causes, cheapest first
Where F4 usually leads
Temperature sensor and calibration.
GE Profile
ovens.
GE Appliances' step-up line, with convection, air fry and combination wall ovens that include speed cooking models.
GE Profile oven repairMore GE Profile codes
Temperature sensor on other makes
Single wall oven
One oven cavity set into a cabinet at chest height, with its own controls above the door and nothing to cook on above it.
Double wall oven
Two full oven cavities stacked in one tall cabinet, sharing one control panel and one power supply but heating on their own.
Speed oven
A compact built-in oven that combines convection heat with microwave energy in one cavity to cook in a fraction of the usual time.
In GE Profile's own words
This code usually means that the oven sensor needs to be replaced.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE Profile wall ovens with electronic controls, such as PT7050 (built 2013-2019), whose support page links the GE code list.
GE Profile F4 oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F4.
Can I clear F4 myself?
Why does my GE Profile show F4 and not F3?
Can I bake with F4 on my GE Profile?
Back to your everyday
Still showing F4?
Book with the code exactly as shown, the full model number, and whether you can smell gas or burning — with a code, that is where the diagnosis starts.