GE Profile wall oven
showing FC
On a GE Profile wall oven, FC means a part of the door lock circuit has stopped working.
Mon–Sat, 8am–8pm
- Door and lock
- Door lock and self-clean repair
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
What FC
actually means.
On a GE Profile wall oven, FC means a part of the door lock circuit has stopped working. The self-clean latch, its switches and wiring are the circuit in question.
GE Profile oven display
What to do when FC shows on the ovenKind of codeDoor and lock
The motorized lock did not reach the position the control asked for, or its switch reported the wrong one. Most often this shows during or after self-clean; the latch, its switches and the door's alignment are checked before the lock motor is replaced.
Usually leads toDoor lock and self-clean repair
A door that stays locked after self-clean, a cycle that will not start or stops early, traced to the lock motor, its switches or the cleaning heat.
Shows up asOven Door Won't Unlock
The door stays latched after a self-clean or a steam clean, or it locked during normal baking and will not release.
MakeGE Profile
GE Appliances' step-up line, with convection, air fry and combination wall ovens that include speed cooking models.
SourceGE Appliances support: Range & Wall Oven error codes
GE Profile wall ovens with self-clean and electronic controls, including PT7050.
Before you book,
in this order.
Each step comes from GE Profile's own guidance for FC on its ovens. Follow it to the end: the last card says whether this is a visit.
Let the oven cool and reset the breaker.
Leave a locked door closed and book a visit; do not force it.
Still there?
It usually turns into door lock and self-clean repair. Book with the code and the model number.
What not to do
FC is not a communication or Wi-Fi code despite the letter C.
What you may
notice with it.
The oven problems FC tends to arrive with. Answer these at the oven before anyone is booked.
All problems
Oven Door Won't Unlock
5 causes, cheapest first
Where FC usually leads
Door lock and self-clean repair.
GE Profile
ovens.
GE Appliances' step-up line, with convection, air fry and combination wall ovens that include speed cooking models.
GE Profile oven repairMore GE Profile codes
Door and lock on other makes
Single wall oven
One oven cavity set into a cabinet at chest height, with its own controls above the door and nothing to cook on above it.
Double wall oven
Two full oven cavities stacked in one tall cabinet, sharing one control panel and one power supply but heating on their own.
Speed oven
A compact built-in oven that combines convection heat with microwave energy in one cavity to cook in a fraction of the usual time.
In GE Profile's own words
This code usually means that a component has failed somewhere in the door lock circuit.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE Profile wall ovens with self-clean and electronic controls, including PT7050.
GE Profile FC oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about FC.
Can I clear FC myself?
Is FC on a GE Profile the same as F9?
My GE Profile shows FC after self-clean and the door will not open. Can I wait it out?
Back to your everyday
Still showing FC?
Book with the code exactly as shown, the full model number, and whether you can smell gas or burning — with a code, that is where the diagnosis starts.