Whirlpool wall oven
showing F3 E1
F3 E1 is the lower-cavity partner of F3 E0 on a Whirlpool double wall oven.
Mon–Sat, 8am–8pm
- Temperature sensor
- Temperature sensor and calibration
- Source: Whirlpool
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F3 E1
actually means.
F3 E1 is the lower-cavity partner of F3 E0 on a Whirlpool double wall oven. The control has flagged the lower oven's temperature sensor, the control board or the wiring that joins them.
Whirlpool oven display
What to do when F3 E1 shows on the ovenKind of codeTemperature sensor
The reading from the temperature probe fell outside what the control will trust, or climbed far higher than the setting. A loose connector or a probe that has drifted is ruled out before the control itself, and a reading that runs away means the breaker goes off first.
Usually leads toTemperature sensor and calibration
Baking that comes out burnt or pale at the usual setting, traced to the sensor, its wiring or an oven that simply needs calibrating.
Shows up asOven Temperature Not Accurate
Recipes come out burnt or underdone at the right setting, and an oven thermometer reads far from the dial.
MakeWhirlpool
A Michigan appliance company that sells widely installed single, double and combination wall ovens.
SourceWhirlpool Product Help: F3 E1 - Wall Oven
Whirlpool double wall ovens and combination units with the F/E code display; the help page does not list models.
Before you book,
in this order.
Each step comes from Whirlpool's own guidance for F3 E1 on its ovens. Follow it to the end: the last card says whether this is a visit.
Cut power at the breaker for a full minute and restore it.
Run the lower oven briefly and watch whether the code reappears.
Book a visit if F3 E1 shows again.
Still there?
It usually turns into temperature sensor and calibration. Book with the code and the model number.
What not to do
F3 E1 is not a door or lock message, even if the lower oven refuses to start while it is displayed.
What you may
notice with it.
The oven problems F3 E1 tends to arrive with. Answer these at the oven before anyone is booked.
All problems
Oven Temperature Not Accurate
5 causes, cheapest first
Where F3 E1 usually leads
Temperature sensor and calibration.
Whirlpool
ovens.
A Michigan appliance company that sells widely installed single, double and combination wall ovens.
Whirlpool oven repairMore Whirlpool codes
Temperature sensor on other makes
In Whirlpool's own words
There may be a problem with the Lower Oven Temperature Sensor, the Control, or the associated wiring.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Whirlpool double wall ovens and combination units with the F/E code display; the help page does not list models.
Whirlpool F3 E1 oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F3 E1.
Can I clear F3 E1 myself?
Is F3 E1 on my Whirlpool the same problem as F3 E0?
Will a new sensor always fix Whirlpool F3 E1?
Back to your everyday
Still showing F3 E1?
Book with the code exactly as shown, the full model number, and whether you can smell gas or burning — with a code, that is where the diagnosis starts.