Whirlpool wall oven
showing F3 E0
On a Whirlpool wall oven, F3 E0 points at the upper cavity: the control no longer trusts what the upper oven's temperature sensor is telling it.
Mon–Sat, 8am–8pm
- Temperature sensor
- Temperature sensor and calibration
- Source: Whirlpool
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F3 E0
actually means.
On a Whirlpool wall oven, F3 E0 points at the upper cavity: the control no longer trusts what the upper oven's temperature sensor is telling it. Whirlpool names three suspects together, the sensor, the control and the wiring between them.
Whirlpool oven display
What to do when F3 E0 shows on the ovenKind of codeTemperature sensor
The reading from the temperature probe fell outside what the control will trust, or climbed far higher than the setting. A loose connector or a probe that has drifted is ruled out before the control itself, and a reading that runs away means the breaker goes off first.
Usually leads toTemperature sensor and calibration
Baking that comes out burnt or pale at the usual setting, traced to the sensor, its wiring or an oven that simply needs calibrating.
Shows up asOven Temperature Not Accurate
Recipes come out burnt or underdone at the right setting, and an oven thermometer reads far from the dial.
MakeWhirlpool
A Michigan appliance company that sells widely installed single, double and combination wall ovens.
SourceWhirlpool Product Help: F3 E0 - Wall Oven
Whirlpool wall ovens with the two-part F/E display codes; the help page names no model series. The E0 suffix marks the upper cavity on double ovens.
Before you book,
in this order.
Each step comes from Whirlpool's own guidance for F3 E0 on its ovens. Follow it to the end: the last card says whether this is a visit.
Switch the oven off at the breaker for one minute, then back on.
Watch the display for a minute to see whether F3 E0 returns.
If it comes back, leave the upper oven unused and book a visit.
Still there?
It usually turns into temperature sensor and calibration. Book with the code and the model number.
What not to do
It does not mean the lower cavity is affected; on a double oven the lower sensor has its own code, F3 E1.
What you may
notice with it.
The oven problems F3 E0 tends to arrive with. Answer these at the oven before anyone is booked.
All problems
Oven Temperature Not Accurate
5 causes, cheapest first
Where F3 E0 usually leads
Temperature sensor and calibration.
Whirlpool
ovens.
A Michigan appliance company that sells widely installed single, double and combination wall ovens.
Whirlpool oven repairMore Whirlpool codes
Temperature sensor on other makes
In Whirlpool's own words
There may be a problem with the Upper Oven Temperature Sensor, the Control, or the associated wiring.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Whirlpool wall ovens with the two-part F/E display codes; the help page names no model series. The E0 suffix marks the upper cavity on double ovens.
Whirlpool F3 E0 oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F3 E0.
Can I clear F3 E0 myself?
Can I keep baking in the lower oven while my Whirlpool shows F3 E0?
Why did F3 E0 come back after I reset the breaker on my Whirlpool?
Back to your everyday
Still showing F3 E0?
Book with the code exactly as shown, the full model number, and whether you can smell gas or burning — with a code, that is where the diagnosis starts.