Maytag wall oven
showing F3 E2
F3 E2 is one of Maytag's F3 group, which covers temperature sensing.
Mon–Sat, 8am–8pm
- Temperature sensor
- Temperature sensor and calibration
- Source: Maytag
Book a visit
Three short steps, about a minute.
or call (844) 407-1890
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F3 E2
actually means.
F3 E2 is one of Maytag's F3 group, which covers temperature sensing. The page names the oven temperature sensor, the control and the wiring between them.
Maytag oven display
What to do when F3 E2 shows on the ovenKind of codeTemperature sensor
The reading from the temperature probe fell outside what the control will trust, or climbed far higher than the setting. A loose connector or a probe that has drifted is ruled out before the control itself, and a reading that runs away means the breaker goes off first.
Usually leads toTemperature sensor and calibration
Baking that comes out burnt or pale at the usual setting, traced to the sensor, its wiring or an oven that simply needs calibrating.
Shows up asOven Temperature Not Accurate
Recipes come out burnt or underdone at the right setting, and an oven thermometer reads far from the dial.
MakeMaytag
A Whirlpool Corporation brand known for sturdy, straightforward appliances, including a small selection of wall ovens.
SourceMaytag Product Help: F3 E2 - Wall Oven
Maytag wall ovens with F/E codes; the page does not name a cavity or model.
Before you book,
in this order.
Each step comes from Maytag's own guidance for F3 E2 on its ovens. Follow it to the end: the last card says whether this is a visit.
Reset the breaker for one minute.
Preheat and see whether the oven reaches temperature without the code.
Book a visit if F3 E2 comes back.
Still there?
It usually turns into temperature sensor and calibration. Book with the code and the model number.
What not to do
It is not a thermostat setting you can adjust; calibration offsets do not clear it.
What you may
notice with it.
The oven problems F3 E2 tends to arrive with. Answer these at the oven before anyone is booked.
All problems
Oven Temperature Not Accurate
5 causes, cheapest first
Where F3 E2 usually leads
Temperature sensor and calibration.
Maytag
ovens.
A Whirlpool Corporation brand known for sturdy, straightforward appliances, including a small selection of wall ovens.
Maytag oven repairMore Maytag codes
Temperature sensor on other makes
In Maytag's own words
There may be a problem with the Oven Temperature Sensor, the Control, or the associated wiring.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Maytag wall ovens with F/E codes; the page does not name a cavity or model.
Maytag F3 E2 oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F3 E2.
Can I clear F3 E2 myself?
Will adjusting the temperature offset clear F3 E2 on my Maytag?
Is my Maytag safe to use with F3 E2 on the display?
Back to your everyday
Still showing F3 E2?
Book with the code exactly as shown, the full model number, and whether you can smell gas or burning — with a code, that is where the diagnosis starts.